Bore | 3.54in |
---|---|
Displacement | 171in³ |
Engine Model | Cat C2.8* |
Maximum Engine Speed | 2550 rpm |
Maximum Gross Power | 74.7hp |
Maximum Gross Power - ISO 14396 | 74.3hp |
Maximum Gross Power - ISO 14396 (metric) | 75.3mhp |
Maximum Gross Power - Rated Engine Speed | 2400r/min |
Maximum Gross Power - SAE J1995 | 74.7hp |
Maximum Gross Torque - ISO 14396 | 221lb/ft |
Maximum Gross Torque - SAE J1995 | 222lb/ft |
Maximum Net Torque - ISO 9249 | 217lb/ft |
Maximum Net Torque - SAE J1349 | 218lb/ft |
Note | Advertised power is tested per the specified standard in effect at the time of manufacture |
Note (1) | Net power advertised is the power available at the flywheel. |
Note (2) | *Two Cat C2.8 engine emission options are available: 1) Meets U.S. EPA Tier 4 Final, EU Stage V. 2) U.S. EPA Tier 3 and EU Stage IIIA equivalent. Tier 3 engine specs are 0.3 kW/0.4 hp more gross power (SAE J1995), 0.2 kW/0.3 hp on net power (SAE J1349) |
Note (3) | #Maximum gross and net torque measured at 1,600 rpm. |
Rated Net Power - 2,400 rpm - ISO 9249 (metric) | 73.1mhp |
Rated Net Power - ISO 9249 | 72.1hp |
Rated Net Power - Rated Engine Speed | 2400r/min |
Rated Net Power - SAE J1349 | 72.7hp |
Stroke | 4.33in |
Operating Weight | 14617lb |
---|
Bucket Capacities | 0.75-1.55 m³ (1.0-2.0 yd³) |
---|---|
Bucket Capacities - General Purpose | 0.80-1.35 m³ (1.0-1.7 yd³) |
Bucket Capacities - Light Material | 1.25-1.55 m³ (1.6-2.0 yd³) |
Multi-Purpose | 0.75-1.1 m³ (1.0-1.4 yd³) |
Note | Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration. |
Note (1) | Bucket capacities stated include BOCE, in line with ISO 7546. |
Recyclability | 93% |
---|
80% of Tip: Firm and Level EN474-3 †† | 4706lb |
---|---|
Articulation Angle - Degrees | 39° |
Carry Height: Bucket Pin | 1.17ft |
Clearance: Bucket at 45° * | 10.92ft |
Clearance: Level Bucket** | 12.08ft |
Clearance: Load over Height** | 10.75ft |
Departure Angle - Degrees | 30° |
Dig Depth** | 0.33ft |
Dump Angle at Full Lift | 40° |
Height: Bucket Pin** | 12.75ft |
Height: Ground Axle Center** | 1.67ft |
Height: Ground Clearance** | 1ft |
Height: Ground to Beacon** | 9.33ft |
Height: Ground to Cab** | 8.75ft |
Height: Overall** | 15.67ft |
Length: Hitch to Front Axle | 3.5ft |
Length: Overall* | 19.67ft |
Length: Rear Axle to Bumper | 4.5ft |
Length: Wheel Base | 7.08ft |
Note (1) | *Vary with bucket |
Note (2) | **Vary with tire |
Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket. |
Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class II |
Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9 |
Operating Weight: Bucket ^ | 14848lb |
Operating Weight: Carriage and Tines ^^ | 14542lb |
Rack Angle at Carry | 48° |
Rack Angle at Full Lift | 69° |
Reach: Bucket at 45° * | 3.25ft |
Tipping Load - Full Turn - ISO 14397-1 † | 7645lb |
Tipping Load - Straight - ISO 14397-1 † | 9187lb |
Tipping Load - Straight † | 9187lb |
Turning Radius: Inside of Tires | 6.5ft |
Turning Radius: Outside of Tires | 13.17ft |
Turning Radius: Over Bucket | 15.83ft |
Width: Bucket | 6.75ft |
Width: Over Tires | 6.67ft |
Width: Tread Center | 5.08ft |
80% of Tip: Firm and Level EN474-3 †† | 4375lb |
---|---|
Articulation Angle - Degrees | 39° |
Carry Height: Bucket Pin | 1.25ft |
Clearance: Bucket at 45° * | 10.42ft |
Clearance: Level Bucket** | 12.08ft |
Clearance: Load over Height** | 10.75ft |
Departure Angle - Degrees | 30° |
Dig Depth** | 0.42ft |
Dump Angle at Full Lift | 40° |
Height: Bucket Pin** | 12.75ft |
Height: Ground Axle Center** | 1.67ft |
Height: Ground Clearance** | 1ft |
Height: Ground to Beacon** | 9.33ft |
Height: Ground to Cab** | 8.75ft |
Height: Overall** | 15.92ft |
Length: Hitch to Front Axle | 3.5ft |
Length: Overall* | 20.17ft |
Length: Rear Axle to Bumper | 4.5ft |
Length: Wheel Base | 7.08ft |
Note (1) | *Vary with bucket |
Note (2) | **Vary with tire |
Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket. |
Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class II |
Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9 |
Operating Weight: Bucket ^ | 15070lb |
Operating Weight: Carriage and Tines ^^ | 14714lb |
Rack Angle at Carry | 42° |
Rack Angle at Full Lift | 66° |
Reach: Bucket at 45° * | 3.42ft |
Tipping Load - Full Turn - ISO 14397-1 † | 6943lb |
Tipping Load - Straight - ISO 14397-1 † | 8385lb |
Tipping Load - Straight † | 8385lb |
Turning Radius: Inside of Tires | 6.5ft |
Turning Radius: Outside of Tires | 13.17ft |
Turning Radius: Over Bucket | 16.17ft |
Width: Bucket | 6.75ft |
Width: Over Tires | 6.67ft |
Width: Tread Center | 5.08ft |
Axles - Front Center Differential | 2.3Gal |
---|---|
Axles - Rear Center Differential | 2.3Gal |
Cooling System | 3.2Gal |
Engine Crankcase | 2.3Gal |
Fuel Tank | 24Gal |
Hydraulic System - Including Tank | 18.6Gal |
Hydraulic Tank | 11.8Gal |
Note | No Diesel Exhaust Fluid (DEF) fluid needed on this size engine. |
Transmission | 0.6Gal |
Front | Fixed (standard), Locking Differential (optional) |
---|---|
Note | Oscillation of ±11 degrees via hitch between front and rear frames. |
Rear | Fixed (standard), Locking Differential (optional) |
Maximum Flow - Steering Pump | 12.3gal/min |
---|---|
Maximum Working Pressure - Steering Pump | 3336psi |
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.25 turns or 4.00 turns |
Steering Articulation Angle - Each Direction | 39° |
Steering Cycle Times – (full left to full right) – at High Idle | 2.8s |
Forward and Reverse - Speed Range 1* | 6mile/h |
---|---|
Forward and Reverse - Speed Range 2** - High Speed | 10.5mile/h |
Forward and Reverse - Speed Range 2** - Standard | 12mile/h |
Forward and Reverse - Speed Range 3*** | 25mile/h |
Forward and Reverse - Speed Range Creep# | 6mile/h |
Note | #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph). |
Note (1) | *Creep function not available in this gear or above. |
Note (2) | **Max speed dependent on model and configuration (standard vs. high speed transmission). |
Note (3) | ***Reverse is 30 km/h (19 mph). |
Note | *This tire has been used for all dimension, stability and performance data. |
---|---|
Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
Note (2) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
Tire Size - Optional | 405/70 R20 Powerloads |
Tire Size - Optional (1) | 400/70 R20 XMCL/Bibload |
Tire Size - Optional (2) | 360/80 R20 TRI 2 |
Tire Size - Optional (3) | 40X14-20 TL, SM/TR |
Tire Size - Standard | *405/70 R20 SPT9 |
FOPS | ISO 3449:2005 Level II |
---|---|
Note (1) | Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU. |
ROPS | ISO 3471:2008 |
Hydraulic Cycle Time - Dump | 1.8s |
---|---|
Hydraulic Cycle Time - Float Down | 3.6s |
Hydraulic Cycle Time - Lift | 5.8s |
Hydraulic Cycle Time - Rackback | 2.5s |
Main Relief - 1st Auxiliary (3rd slice) | 3408psi |
Main Relief - 1st Auxiliary (3rd slice) - High Flow* | 33gal/min |
Main Relief - 1st Auxiliary (3rd slice) - Standard Flow* | 24gal/min |
Main Relief - 2nd Auxiliary (4th slice) | 3408psi |
Main Relief - 2nd Auxiliary (4th slice) - Flow | 12gal/min |
Note | * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display. |
80% of Tip: Firm and Level EN474-3 †† | 5815lb |
---|---|
Articulation Angle - Degrees | 39° |
Carry Height: Bucket Pin | 1.17ft |
Clearance: Bucket at 45° * | 8.58ft |
Clearance: Level Bucket** | 10.5ft |
Clearance: Load over Height** | 9.75ft |
Departure Angle - Degrees | 30° |
Dig Depth** | 0.33ft |
Dump Angle at Full Lift | 45° |
Height: Bucket Pin** | 11.17ft |
Height: Ground Axle Center** | 1.67ft |
Height: Ground Clearance** | 1ft |
Height: Ground to Beacon** | 9.33ft |
Height: Ground to Cab** | 8.75ft |
Height: Overall** | 14.17ft |
Length: Hitch to Front Axle | 3.5ft |
Length: Overall* | 18.17ft |
Length: Rear Axle to Bumper | 4.5ft |
Length: Wheel Base | 7.08ft |
Note (1) | *Vary with bucket |
Note (2) | **Vary with tire |
Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket. |
Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class II |
Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9 |
Operating Weight: Bucket ^ | 14633lb |
Operating Weight: Carriage and Tines ^^ | 14252lb |
Rack Angle at Carry | 51° |
Rack Angle at Full Lift | 53° |
Reach: Bucket at 45° * | 2.33ft |
Tipping Load - Full Turn - ISO 14397-1 † | 8895lb |
Tipping Load - Straight - ISO 14397-1 † | 10626lb |
Tipping Load - Straight † | 10626lb |
Turning Radius: Inside of Tires | 6.5ft |
Turning Radius: Outside of Tires | 13.17ft |
Turning Radius: Over Bucket | 14.75ft |
Width: Bucket | 6.75ft |
Width: Over Tires | 6.67ft |
Width: Tread Center | 5.08ft |
80% of Tip: Firm and Level EN474-3 †† | 5438lb |
---|---|
Articulation Angle - Degrees | 39° |
Carry Height: Bucket Pin | 1.25ft |
Clearance - Bucket at 45° | 8.25ft |
Clearance - Level Bucket | 10.5ft |
Clearance: Load over Height** | 9.75ft |
Departure Angle - Degrees | 30° |
Dig Depth | 0.45ft |
Dump Angle at Full Lift | 48° |
Height - Bucket Pin | 11.17ft |
Height - Ground Clearance | 1ft |
Height - Ground to Cab | 8.75ft |
Height: Ground Axle Center** | 1.67ft |
Height: Ground to Beacon** | 9.33ft |
Height: Overall** | 14.42ft |
Length - Overall with Bucket | 18.67ft |
Length - Wheel Base | 7.08ft |
Length: Front Axle to Front of Coupler | 4.75ft |
Length: Hitch to Front Axle | 3.5ft |
Length: Rear Axle to Bumper | 4.5ft |
Note (1) | *Vary with bucket |
Note (2) | **Vary with tire |
Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket. |
Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class II |
Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9 |
Operating Weight: Bucket ^ | 14752lb |
Operating Weight: Carriage and Tines ^^ | 14391lb |
Rack Angle at Carry | 54° |
Rack Angle at Full Lift | 50° |
Reach - Bucket at 45° | 2.67ft |
Tipping Load - Full Turn - ISO 14397-1† | 6800lb |
Tipping Load - Straight † | 9753lb |
Tipping Load – Full Turn – ISO 14397-1 † | 8141lb |
Tipping Load – Straight – ISO 14397-1 † | 9581lb |
Turning Radius - Inside Tire | 6.67ft |
Turning Radius - Over Bucket | 15.08ft |
Turning Radius: Outside of Tires | 13.17ft |
Width - Bucket | 6.75ft |
Width - Over Tires | 6.67ft |
Width - Tread Center | 5.08ft |