| Bore | 3.85in |
|---|---|
| Displacement | 220in³ |
| Emissions | Engine meets Tier 4 Final/Stage V emission standards. |
| Engine Model | Cat C3.6 |
| Maximum Gross Power | 121hp |
| Maximum Gross Power - ISO 14396 | 121hp |
| Maximum Gross Power - ISO 14396 (metric) | 122hp |
| Maximum Gross Power - Rated Engine Speed | 2200r/min |
| Maximum Gross Torque - ISO 14396 | 369ft·lbf |
| Maximum Gross Torque - SAE J1995 | 372ft·lbf |
| Maximum Net Torque - ISO 9249 | 363ft·lbf |
| Maximum Net Torque - SAE J1349 | 366ft·lbf |
| Note | Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator. |
| Rated Net Power - ISO 9249 | 118hp |
| Rated Net Power - Rated Engine Speed | 2200r/min |
| Rated Net Power - SAE J1349 | 120hp |
| Stroke | 4.72in |
| Operating Weight | 21742lb |
|---|
| Bucket Capacities | 1.3-3.5 m3 (1.7-4.6 yd3) |
|---|---|
| Bucket Capacities - General Purpose | 1.3-1.9 m³ (1.7-2.5 yd³) |
| Bucket Capacities - Light Material | 2.5-3.5 m³ (3.3-4.6 yd³) |
| Recyclability | 95% |
|---|
| Axles - Front | 4.5gal (US) |
|---|---|
| Axles - Rear | 4.5gal (US) |
| Cooling System | 5.7gal (US) |
| Diesel Exhaust Fluid (DEF) Tank | 4.8gal (US) |
| Engine Crankcase | 2.6gal (US) |
| Fuel Tank | 43.6gal (US) |
| Hydraulic System - Including Tank | 25.9gal (US) |
| Hydraulic Tank | 14.5gal (US) |
| Note | DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
| Transmission | 0.8gal (US) |
| FOPS | ISO 3449:2005 |
|---|---|
| Note (1) | Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe. |
| Note (2) | The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A). |
| Note (3) | The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A). |
| Note (4) | *The measurements were conducted with the cab doors and windows closed. |
| ROPS | ISO 3471:2008 |
| Maximum Flow - Steering Pump | 21.7gal/min |
|---|---|
| Maximum Working Pressure - Steering Pump | 3190psi |
| Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.4turns |
| Steering Articulation Angle - Each Direction | 40° |
| Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed | 2.3s |
| Hydraulic Cycle Time - Dump, at Maximum Reach | 1.8s |
|---|---|
| Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level | 2.7s |
| Hydraulic Cycle Time - Rackback | 2.2s |
| Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift | 4.8s |
| Hydraulic Cycle Time - Total Cycle Time | 11.5s |
| Maximum Flow - Implement Pump | 43.6gal/min |
| Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High | 40gal/min |
| Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard | 25gal/min |
| Maximum Flow - Implement Pump - 4rd Function, Maximum Flow | 25gal/min |
| Maximum Working Pressure - Implement Pump | 4061psi |
| Note | All cycle times listed are with cylinder snubbing turned off. |
| Relief Pressure - Tilt Cylinder | 4641psi |
| Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure | 4641psi |
| Forward and Reverse - Speed Range 1* | 6.3mile/h |
|---|---|
| Forward and Reverse - Speed Range 2* | 12.5mile/h |
| Forward and Reverse - Speed Range 3 | 25mile/h |
| Note | *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1. |
| Front | Fixed; Locking differential (standard) |
|---|---|
| Rear | Oscillating ±11 degrees; Locking differential (standard) |
| Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
|---|---|
| Note (2) | In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities. |
| Note (3) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
| Other Choices Include | 17.5 R25 L3 XHA2; 20.5 R25 L3 XHA3; 17.5-25 L2/L3 SGL; 20.5-25 L2/L3 SGL; 17.5-25 L3 HRL D/L-3A; 17.5 R25 L2 Snow; 20.5 R25 L2 Snow; 17.5 R25 Solid |
| Standard Size | 17.5 R25 L2 XTLA |
