| Body Capacity - SAE 2:1 | 83.1yd³ |
|---|---|
| Maximum Allowable Payload (120%)* | 121.3ton (US) |
| Maximum Working Payload (110%) | 111.2ton (US) |
| Note (1) | Capacity with flat floor X Body with liner. |
| Note (2) | * Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross vehicle weight limitations. |
| Target Payload (100%) | 101.1ton (US) |
| Top Speed - Loaded | 40.9mile/h |
| Bore | 5.7in |
|---|---|
| Cylinders | 12 |
| Displacement | 1959in³ |
| Engine Model | Cat® C32B |
| Engine Power - ISO 14396 | 1008hp |
| Engine Speed | 1800r/min |
| Gross Power - SAE J1995:2014 | 1025hp |
| Net Power - SAE J1349:2011 | 916hp |
| Net Torque Rise | Tier 4: 39%. Tier 2: 37% |
| Note (1) | Power rating applies at 1,800 rpm when tested under the specified condition for the specified standard. |
| Note (2) | Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F). |
| Note (3) | Available as U.S. EPA Tier 4 Final/EU Stage V equivalent, Tier 3/Stage IIIA equivalent, or Tier 2/Stage II equivalent emission standards. |
| Note (4) | Meets China Nonroad Stage III emission standards equivalent to Tier 3 or Tier 2. |
| Peak Torque - Speed | 1200r/min |
| Stroke | 6.4in |
| Heaped (SAE 2:1)* | 83.8yd³ |
|---|---|
| Note (1) | Contact your local Cat dealer for body recommendation. |
| Note (2) | *ISO 6483:1980 |
| Struck | 56.3yd³ |
| SAE 2:1 - For use with material densities less than 950 kg/m3 (1,600 lb/yd3) | 164.6yd³ |
|---|---|
| SAE 2:1 - For use with material densities of 1040-1160 kg/m3 (1,750-1,950 lb/yd3) | 139yd³ |
| SAE 2:1 - For use with material densities of 1160 kg/m3 (1,950 lb/yd3) | 116.8yd³ |
| SAE 2:1 - For use with material densities of 950-1040 kg/m3 (1,600-1,750 lb/yd3) | 144yd³ |
| Heaped (SAE 2:1)* | 78.6yd³ |
|---|---|
| Note (1) | Contact your local Cat dealer for body recommendation. |
| Note (2) | *ISO 6483:1980 |
| Struck | 54.8yd³ |
| Front Axle - Empty | 42% |
|---|---|
| Front Axle - Loaded | 33% |
| Rear Axle - Empty | 58% |
| Rear Axle - Loaded | 67% |
| Forward - 1 | 6.6mile/h |
|---|---|
| Forward - 2 | 9.1mile/h |
| Forward - 3 | 11.9mile/h |
| Forward - 4 | 16.6mile/h |
| Forward - 5 | 22.5mile/h |
| Forward - 6 | 30.2mile/h |
| Forward - 7 | 40.9mile/h |
| Note | Maximum travel speeds with standard 27.00R49 (E4) tires. |
| Reverse | 7.5mile/h |
| Differential Ratio | 2.736:1 |
|---|---|
| Planetary Ratio | 7.0:1 |
| Total Reduction Ratio | 19.1576:1 |
| Brake Standards | ISO 3450-2011 |
|---|---|
| Brake Surface Area - Front | 6331in² |
| Brake Surface Area - Rear | 15828in² |
| Brake Hoist System | 117gal (US) |
|---|---|
| Cooling System | 61gal (US) |
| Crankcase | 28.7gal (US) |
| Differentials | 59.9gal (US) |
| Final Drive - Each | 20gal (US) |
| Fuel Tank (1) | 300gal (US) |
| Fuel Tank (2) | 350gal (US) |
| Steering System - Including Tank | 14.1gal (US) |
| Torque Converter - Transmission System | 36.5gal (US) |
| Body Lower Time - Float | 13s |
|---|---|
| Body Lower Time - High Idle | 13s |
| Body Raise Time - High Idle | 15s |
| Pump Flow - High Idle | 120.9gal/min |
| Relief Valve Setting - Lower | 500psi |
| Relief Valve Setting - Raise | 2750psi |
| Empty Loaded Cylinder Stroke Front | 2.9in |
|---|---|
| Empty Loaded Cylinder Stroke Rear | 2.5in |
| Rear axle - Oscillation | 5.4° |
| Note (1) | Productive capabilities of the 777 truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production. |
|---|---|
| Note (2) | Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection. |
| Standard Tire | 27.00R49 (E4) |
| Target Gross Machine Weight | 363000lb |
|---|
| FOPS Standards | Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria. |
|---|---|
| ROPS Standards | Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria. |
| Steer Angle | 30.5° |
|---|---|
| Steering Standards | ISO 5010:2007 |
| Turning Circle - Clearance Diameter | 93ft |
| Turning Diameter - Front | 83ft |
| Sound Standards (1) | The operator Equivalent Sound Pressure Level (Leq) is 73 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with t |
|---|---|
| Sound Standards (2) | The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 83 dB(A). |
| Sound Standards (3) | Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment. |
